Call us: +61 2 9838 8899
FAX: +61 2 9838 8818

Blog

Home»Blog»New Firmware and Application Notes for DrayTek Products (8 August 2017)

New Firmware and Application Notes for DrayTek Products (8 August 2017)

New Video


6 Hidden Features in the DrayTek Vigor Router Dashboard

DrayTek has designed a Dashboard page for Vigor routers providing information on the router status as well as shortcuts to configuration menus. This video describes each of these features. The features include: the DrayTek Home, GUI Map, Web Console, Configuration Backup, Logout and Topology Icons.

Watch now


New Application Notes


VPN

Vigor Router to Vigor Router – PPTP

This document shows how to establish a PPTP LAN-to-LAN VPN tunnel between two Vigor Routers.

Read more


IPsec Tunnel between two Vigor Routers with the same IP subnet

This document shows how to create an IPsec LAN to LAN VPN tunnel between two offices where both routers have the same LAN IP subnet. It uses the Virtual IP mapping feature in the “IPsec VPN with the Same Subnets” setting option available in the latest firmware for Vigor2860 and Vigor2925 routers.

Read more


Vigor Router to Vigor Router – L2TP over IPsec

This application note shows how to establish a L2TP over IPsec VPN tunnel between two Vigor Routers.

Read more


Vigor Router to Teltonika RUT950 Router – GRE Tunnel

This document introduces how to set up GRE tunnel between a Vigor DrayOS Router and Teltonika RUT950.

Read more


Vigor3900 to Teltonika RUT950 Router – GRE Tunnel

This document introduces how to set up GRE tunnel between a Vigor3900 or Vigor2960 Router and Teltonika RUT950.

Read more


Application

What is High Availability?

This updated application note gives an overview of High Availability and how it works. It also explains the differences between Hot-Standby and Active-Standby modes.

Read more


WAN

[Vigor3900] How to use Virtual WAN in bridge mode?

This application note shows how to set up Bridge WAN for IPTV on the Vigor3900 and Vigor2960 routers.

Read more


Central AP Management

[Vigor3900] How to provision a VigorAP by AP Management (APM)?

This application note describes how to provision VigorAP’s using the AP Management (APM) feature on Vigor3900/2960/300B routers.

Read more


IPPBX

How to Grab an unattended incoming Call

This application note shows how to answer an incoming call on the IPPBX for an unattended extension

Read more


Firmware

How to upload firmware to my Vigor Route via FTP?

This application note shows how to install firmware into Vigor routers by using the FTP method

Read more


How to recover my Vigor Router when it does not response?

This application note describes the process to recover a router if the firmware has become damaged resulting in an unresponsive router.

Read more


NAT

How to enable ALG (Application Layer Gateway)?

Due to the protocols like SIP, RTSP and FTP are short of NAT-T, so when the service server is behind NAT, the connection could fail. ALG is able to resolve this issue. With ALG enabled, Vigor router will replace the private IP with public IP in the negotiation packet from the client and open dynamic TCP/UDP ports required in the connection.

Read more


Firmware Updates


 
Vigor Manager for iOS V1.1.2

This new version includes some bug fixes.

Click here to download


Vigor2860/Vigor2860L V3.8.4.6

New feature
  • Support BGP.
Improvements
  • WAN1 increased time out during LCP Terminate-ACK.
  • IPsec traffic wasn’t passed to VPN server at Vigor2860 routing subnet.
  • DDNS update problem occurred when 3G modem, PPP mode was used.

Click here to download


Vigor2760 Delight V3.8.2.3

New Feature

  • Support VigorACS 2.0.

Improvements

  • Add an option to Disable TLS 1.0.
  • Add telnet command for configuring VPN Dial-out through.
  • Add a new option “MS-CHAPv2 Only” for Dial-In PPP Authentication.
  • LAN client could access Vigor router across VLAN.
  • NAT loopback did not work when DMZ was enabled.
  • Ping Diagnosis of diagnostics interface was displayed incorrectly when ping through VPN tunnel.

Click here to download


Vigor2960 V1.3.1

New Feature

  • Add Fast Route function to reduce CPU loading (Routing>>Fast Route).

Improvements

  • Improvements to make security updates for Samba service (CVE-2017-7494).
  • Update SSH server to new version (2016.74).
  • Update APP signatures for Hotspot, UltraSurf, PPstream and Google Hangouts.

For a complete list of improvements, refer to the release notes in the download link below.

Click here to download


VigorAP 710 V1.2.1

Some of the new features include

  • Wireless connection will be disabled automatically if there is no internet access.
  • Add schedule mechanism to re-select wireless channel.
  • Support TLS 1.2.
  • Add parameters required for being managed by VigorACS2.

For a full list of new features and bug fixes, refer to the release notes in the download link.

Click here to download


VigorAP 810 V1.2.1

Some of the new features include

  • Wireless connection will be disabled automatically if there is no internet access.
  • Add schedule mechanism to re-select wireless channel.
  • Support TLS 1.2.
  • Add parameters required for being managed by VigorACS2.

For a full list of new features and bug fixes, refer to the release notes in the download link.

Click here to download

Written by

The author didnt add any Information to his profile yet